HSM shredstar Series

The paper detector/ rocker switch in the insertion slot is defective. Please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please contact our customer service.

Please check that the upper part is seated correctly. A "click" should be heard when placing it. This noise is caused by a small plastic nose which is on the inside of the viewing window (on the collecting container). If this plastic nose is broken or bent, the contact switch on the top part cannot be pressed properly and the power connection is not enabled. If there is no viewing window, please contact our customer service.

Please check if you have inserted more than 10 sheets of 80g paper at the same time. Reverse the blockage by setting the sliding switch to "Rev". If the jam cannot be removed, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please contact our customer service.

Please check that the upper part is seated correctly. A "click" should be heard when placing it. This noise is caused by a small plastic nose which is on the inside of the viewing window (on the collecting container). If this plastic nose is broken or bent, the contact switch on the top part cannot be pressed properly and the power connection is not enabled. If there is no viewing window, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

The engine of the document shredder has overheated. Please let the machine cool down for about 60 minutes. As soon as the red LED goes out, you can restart the machine.  If the error cannot be solved by the described procedure, please contact our customer service.

Please check if you have inserted more than 5 sheets of 80g paper at the same time. Reverse the blockage by setting the sliding switch to "Rev". If the cutting unit is not clogged, you should oil it with special HSM oil. If the error cannot be solved by the described procedure, please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please contact our customer service.

Please check that the upper part is seated correctly. A "click" should be heard when placing it. This noise is caused by a small plastic nose which is on the inside of the viewing window (on the collecting container). If this plastic nose is broken or bent, the contact switch on the top part cannot be pressed properly and the power connection is not enabled. If there is no viewing window, please contact our customer service.

The engine of the document shredder has overheated. Please let the machine cool down for about 60 minutes. As soon as the red LED goes out, you can restart the machine.  If the error cannot be solved by the described procedure, please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Please remove the power plug and empty the cut paper container. If this is not full, please check the fill level sensor at the bottom of the top part. If this is dirty, you can clean it with a dry brush or soft cloth. If the LED still does not go out, please contact our customer service.

Please check if you have inserted more than 6 sheets of 80g paper at the same time. Reverse the blockage by setting the sliding switch to "Rev". If the cutting unit is not clogged, you should oil it with special HSM oil. If this does not remove the error, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please contact our customer service.

The engine of the document shredder has overheated. Please let the machine cool down for about 60 minutes. As soon as the red LED goes out, you can restart the machine.  If the error cannot be solved by the described procedure, please contact our customer service.

Please check that the upper part is seated correctly. A "click" should be heard when placing it. This noise is caused by a small plastic nose which is on the inside of the viewing window (on the collecting container). If this plastic nose is broken or bent, the contact switch on the top part cannot be pressed properly and the power connection is not enabled. If there is no viewing window, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Please check if you have inserted more than 6 sheets of 80g paper at the same time. Reverse the blockage by setting the sliding switch to "Rev". If the cutting unit is not clogged, you should oil it with special HSM oil. If this does not remove the error, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please contact our customer service.

The engine of the document shredder has overheated. Please let the machine cool down for about 60 minutes. As soon as the red LED goes out, you can restart the machine.  If the error cannot be solved by the described procedure, please contact our customer service.

Please check if you have inserted more than 10 sheets of 80g paper at the same time. Reverse the blockage by setting the sliding switch to "Rev". If the cutting unit is not clogged, you should oil it with special HSM oil.

Please check that the upper part is seated correctly. A "click" should be heard when placing it. This noise is caused by a small plastic nose which is on the inside of the viewing window (on the collecting container). If this plastic nose is broken or bent, the contact switch on the top part cannot be pressed properly and the power connection is not enabled. If there is no viewing window, please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Please remove the power plug and empty the cut paper container. If this is not full, please check the fill level sensor at the bottom of the top part. If this is dirty, you can clean it with a dry brush or soft cloth. If the LED still does not go out, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please empty the cut paper container. If the display remains lit, please clean the fill level sensor, which is at the bottom of the cutting head. This is to be cleaned with a dry brush, compressed air or a soft cloth. If the LED still does not go out, please contact our customer service.

This problem can arise if the engine was overloaded. In this case, please let the document shredder cool down for about 30 minutes before restarting it. If this does not solve the problem, please contact our customer service.

This indicates a defective controller. Please contact our customer service.

If there is a paper jam, the display in the control panel lights up and the machine is automatically set to reverse. This pushes the paper back and the paper jam is removed. If the paper is not pushed out far enough automatically, press and hold the "REV" key to remove it.  If this does not remove the paper jam, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

Please empty the cut paper container. If the display remains lit, please clean the fill level sensor, which is at the bottom of the cutting head. This is to be cleaned with a dry brush, compressed air or a soft cloth. If the LED still does not go out, please contact our customer service.

This problem can arise if the engine was overloaded. In this case, please let the document shredder cool down for about 30 minutes before restarting it. If this does not solve the problem, please contact our customer service.

This indicates a defective controller. Please contact our customer service.

If there is a paper jam, the display in the control panel lights up and the machine is automatically set to reverse. This pushes the paper back and the paper jam is removed. If the paper is not pushed out far enough automatically, press and hold the "REV" key to remove it.  If this does not remove the paper jam, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Please contact our customer service.

Please empty the cut paper container. If the display remains lit, please clean the fill level sensor, which is at the bottom of the cutting head. This is to be cleaned with a dry brush, compressed air or a soft cloth. If the LED still does not go out, please contact our customer service.

The cutting unit should be oiled if cutting performance decreases, a sound develops and after emptying the paper container. Inject the special oil over the entire width of the feed slot onto the blade shafts. Then, press the "R" key to reverse the cutting unit until all paper residues are released. If this does not solve the problem, please contact our customer service.

Try to soften the cutting unit with plenty of oil. Please make sure that there is some paper in the collecting container to avoid unnecessary soiling. Once the blockage has been softened a bit, try to push it downwards using a thin piece of cardboard. If this does not remove the jam, please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

This problem can arise if the engine was overloaded. In this case, please let the document shredder cool down for about 30 minutes before restarting it. If this does not solve the problem, please contact our customer service.

This indicates a defective controller. Please contact our customer service.

If there is a paper jam, the display in the control panel lights up and the machine is automatically set to reverse. This pushes the paper back and the paper jam is removed. If the paper is not pushed out far enough automatically, press and hold the "REV" key to remove it.  If this does not remove the paper jam, please contact our customer service.

The light barrier in the insertion slot is defective. Please contact our customer service.

Please check if the insertion slot is clogged. If this is not the case, please contact our customer service.

The light barrier is interrupted. It can be cleaned with compressed air. Please make sure that you clean both the sender and the receiver; sender is in the paper feed slot and the receiver in the CD feed slot. If this does not remove the fault, please contact our customer service.

Please contact our customer service.