used VK 4812P//Technical Data/Main drive power: 15 kW/Motor efficiency class IE3 according to IEC standard 60034/30/Total drive power: depends on additional equipment/Voltage / Frequency: 3 x 400 V / 50 Hz + N + PE/Pressing force: 480 kN/Specific pressing force: 58 N/cm²/Pump flow rate: 102 l/min/Tank capacity: 300 l/Filling opening (W x L): 1020 x 1250 mm/Bale/channel cross-section (W x H): 1100 x 750 mm/Bale length adjustable in 4 steps: 600 - 1200 mm/Bale weight at 1200 mm bale length: approx. 300 - 550 kg/or standardized bale weight (per m³): approx. 300 - 550 kg/(depending on material)/Cycle time (idle press stroke forward and back): approx. 24.50 sec/Theoretical volume throughput: 151 m³/h/Theoretical throughput at bulk density:/20 kg/m³ = approx. 3.02 t/h/50 kg/m³ = approx. 7.55 t/h//Technical Description HSM VK 4812 P///Special filling chute (snout design)/for manual rear loading via existing ramp/with push-through cylinders on the right (viewed in pressing direction)/Control cabinet positioned to the left of the snout chute on the ramp///Fully automatic pressing///Fully automatic horizontal 4-fold strapping using patented wire spools///Pressing interval control via light barrier///2450 mm pressing channel, conical///Cone angle hydraulically adjusted depending on material///Programmable logic controller Siemens S7-1200, with/text display and diagnostic memory: important/operating states displayed in plain text///Bale counter integrated in text display///Operating hours counter///Press box floor in wear zone made of Hardox///Side channel sealing with upper dirt strip/on both sides for special applications (e.g. PET)///Wear plate lining with additional welded wear plates/in the bottom part of the pressing channel///Wire slot covers on press plate front prevent/entry of contaminants into push-through channels///Retention system: 6 brake wedges in channel floor and/ceiling area to increase friction of pressed material///Shortened and compact cascade design at rear of baler///Standard paint finish:/Press: RAL 7011 (iron grey)/Cylinder, motor, control cabinet: RAL 9002 (grey white)/Machine base weight without additional equipment: approx. 9.5 - 10 tons/includes technical documentation, 3 copies, in German/Includes GS mark (Tested Safety) and CE Declaration of Conformity//Optional Equipment///Oil cooler, cooling capacity 9 kW/for 15 kW main drive baler/(motor power 1.5 kW) for continuous operation under high load/or high ambient temperatures///Control cabinet heater/for installation in unheated halls or under shelters,/temperature < 10 °C///Tank heater/for installation in unheated halls or under shelters,/temperature < 4 °C///Press shutdown/automatic shutdown when "wire end" is detected///Special wire station for 250/500 kg wire coils/placed separately next to the press,/incl. wire feed to baler/(initial wire supply not included!)///Initial wire supply/8 coils à 250 kg/coil (3.8 mm)///Bale chute/to compensate for height difference/between press channel and floor level ± 0, length approx. 3300 mm///Special filling chute (snout)/for manual loading from existing ramp///Control panel at separate location/with operating functions and text display;/supply lines and cable ducts included/(max. 10 m radius from press)///Optical warning signal/2 flashing lights (1x red / 1x blue)/mounted on baler control cabinet/to indicate general faults and cleaning strokes///Remote maintenance system/for external data analysis and processing///Central lubrication of press plate/via progressive lubricant distributor – manual//Transport carts for wire coils / 8 pcs/mobile, each equipped with swivel and locking wheels//Emergency stop strip/mounted on the filling chute of the press//Technische und optische Änderungen vorbehalten/Produktbild ist ein Beispielbild//Lieferzeit: auf Anfrage//Änderungen und Irrtümer vorbehalten